S0009211

Water tank kit,Complete,w.SteelRoof,70m3


Complete cylindrical Steel Reinforced Water Storage Tank with Liner, Roof and Distribution Tap Stands, having a volume of 70,000 liters, similar to "OXFAM T70" water tank type. Kit comes with STEEL roof.
Indicative Price 8,508.00 USD

General Description:
Complete cylindrical Steel Reinforced Water Storage Tank with Liner, Roof and Distribution Tap Stands, having a volume of 70,000 liters (70 cubic meters). This kit comes with STEEL roof.

The tank structure and mounting principles are similar to the "OXFAM" (T70) water tank type commonly employed for storing drinking water in emergency situations.

Technical Specifications:
This large 70m³ tank is suitable for use for bulk water distribution to larger groups of people and some water treatment processes. The rapid response tanks are very simple to install, and can be dismantled and re-used elsewhere.

The water tank comes in compact packed sub-kits for easy shipment and mounting on-site, each sub-kit containing all the necessary accessories.

Each complete water tank kit includes following sub-kits:
1/- Steel frame kit = the outer corrugated steel sheets,
2/- Liner kit = the inner synthetic rubber liner,
3/- Steel Roof kit = the STEEL roof cover.
4/- Distribution kit = 2 sets of distribution tap stand kits
5/- Connection kit = appropriate connection hose kit for connecting water tank and tap stands.
6/- Tool kit = Installation tool kit

The kit is supplied with 2 sets of distribution Tap Stand kits as per UNICEF Catalogue no. S0005831 - and, as appropriate, connection hose kit with quick couplings for connecting the tap stand kits.

THE FOLLOWING COMPOSITIONS OF EACH SUB-KIT CAN BE SUBJECT FOR SLIGHT DEVIATIONS ON MATERIALS AND COMPONENTS DEPENDING ON THE EXACT MANUFACTURER/SUPPLIER OF WATER TANK SET. HOWEVER, CONSTRUCTION PRINCIPLES, STRENGTH CONDITIONS, AND SUITABILITY FOR USE WITH CHLORINATED DRINKING WATER SHALL BE COMPLIANT.

1) CORRUGATED STEEL SHEET KIT for the 70,000 liters tank:

These corrugated steel sheets will form a cylindrical tank measuring approximately 6.4 meters in diameter and 2.3 meters high. It is designed to support a heavy duty flexible liner, and to be used for semi-permanent installations. The kit includes all fixings/fittings and accessories.

Item 1:
18 x 6.4 m Ø x 0.8 mm corrugated galvanized steel sheets measuring 3.0 m long x 0.8 m high, drilled with 14 mm holes on all sides (plain). Minimum tensile strength of all panels should be 90kN including a safety margin of 25% over maximum required design strength - this permits the sheets to be interchangeable and used in different tank sizes up to 95m3.

Item 2:
2 x Sheet as item 1, but one hole drilled 95 mm Ø for receiving a 3" Ø Table D/E flanged spigot, i.e. with 4 No 17 mm Ø bolt holes on 146 mm bolt circle diameter, at mid-point of long side of sheet 175 mm from edge to centre of hole.

Item 3:
1 x Sheet as Item 2 drilled identically, but with centre of hole at centre of sheet. Hole to be blanked off with 225 mm square plate made from same material and fixed in place with 4 No M10 x 20 mm round head bolts and nuts.


2) TANK LINER and accessories

This cylindrical water tank liner is normally made from reinforced synthetic rubber, measures approximately 6.4 meters in diameter and 2.3 meters high, to suit the corrugated steel frame. It is suitable for potable water use. The kit includes all fixings/fittings and accessories.

Item 1:
1 x 21 m length of 12 mm Ø split plastic primary wall capping
Item 2:
1 x 21 m length of 25 mm Ø split plastic secondary wall capping.
Item 3:
60 x 25 mm Ø steel spring clips
Item 4:
1 x Bag containing: 560 M10 Ø x 20 mm zinc plated round head bolts, 560 M10 zinc plated nuts, 560 M10 zinc plated washers.

Item 5: 2 x 3" Ø BSP (F) brass gate valve
Item 6: 3 x 55 m roll of 50 mm wide cloth-based waterproof self-adhesive tape
Item 7: 4 x 3" Ø BSP (F) Table D/E flange, 4 plain holes drilled for bolts.
Item 8: 4 x 3" Ø Table D/E flange welded to 90 mm long 3" Ø pipe threaded 40 mm at the free end, 4 holes drilled for M16 bolts and 4 holes threaded for M16 studs. Weld shoulder must not exceed 6 mm x 6 mm
Item 9: 16 x M16 Ø steel studs 100 mm long, each complete with 2 M16 hex full nuts and 2 x M16 washers type B (thin).
Item 10: 8 x 3" Ø Table D/E synthetic rubber gasket - 4 holes, 2 mm thick.
Item 11: 1 x 1.25 mm thick (tolerance - 2% to + 10%) scrim reinforced EPDM synthetic rubber tank liner, suitable for potable water use, welded to fit 6.4 m Ø x 2.3 m high tank ring and allowing minimum 300 mm turndown on outside with eyelets spaced at 1 m centres around edge. The liner is designed to be resistant to UV, temperature extremes and chlorine. The liner material is certified to US-EPA, NSF or EU national standards for not leaching into the water any component (softener, heavy metal, etc.) that may/might be of potential human health risk.
Item 12: 1 x Repair kit for Item 11, comprising: 1 m2 liner material, 10 m roll of 50 mm wide patching tape.
Item 13: 3 x 12 m roll PTFE jointing tape, 12 mm wide
Item 14: 1 x 100 m length of 6 mm polypropylene rope, ultra-violet stabilized.
Item 15: 14 x Steel pegs 450 mm long x 10 mm Ø
Item 16: 2 x 17 mm open ended podger/ spanner
Item 17: 1 x Water Storage Pack (Mounting) Manual, to be placed inside a grip-seal (plastic) bag.
Item 18: 2 x 3" BSP (M) to 2" Guillemin Quick Coupling

3) TANK ROOF, Universal - STEEL cover

The steel roof provides extra rigidity, strength and protection for the tank and can extend the tank service life considerably

While the standard Tank Roof Kit from uPVC is not designed to withstand severe weather conditions, this rigid Roof Kit from STEEL is highly recommended for such locations where risk of severe weather like heavy rainfalls, snow and/or wind is normal.
It is especially recommended where longevity is required, i.e. for use with semi-permanent installations, as it will endure more extreme weather conditions, and requires little maintenance.

This universal steel roof kit fits all three 45, 70 and 95 m3 tank kits of the "Oxfam type" dimensions.
When used with the 95 m3 water tank all centre poles and sockets will be required.

This universal, rigid, Steel Roof Kit is suitable for rigid steel reinforced tanks with a common diameter of expected 6.4 m for the different tank sizes of 45m3, 70m3 and 95m3 of the Oxfam rigid tank type (ref.: UNICEF Codes S0009206, S0009207, S0009205 (w/uPVC Roofs), and UNICEF Codes S0009209, S0009xx, S0009210 (w/Steel Roofs), all similar to Oxfam Codes T45, T70, T95).

The overall fall of the roof should be 1.26 m. Poles should not be cut on site to reduce roof pitch, as this may cause ponding of water on the roof and subsequent damage of tank sheets.
An inspection hatch has been added to avoid having to loosen the roof each time the inside of the tank needs to be examined, or where chemical dosing needs to be undertaken.

EACH STEEL ROOF KIT IS SUPPLIED WITH:
3.07m long roof panels, one with access hatch cut
Base plate, centre plates and poles for roof support system
Access/inspection hatch to fit cut panel, top hinged, with hasp for padlock, to allow easy access for dosing etc
DANGER DEEP WATER sticker for outside of tank
Sufficient support brackets, nuts, bolts and washers for assembly and fixing to tank
Full assembly instructions
Roof retaining straps

Details of Components included:

Item# Qty Unit Description
1 20 Each Roof panel plain, 3073mm long, GI
2 1 Each Roof panel with access hole, 3073mm long, GI
3 1 Each Centre plate, outer, drilled to match segments, GI
4 1 Each Centre plate, inner, GI
5 1 Each Water tank hatch with hasp for padlock,
top hinged, GI
6 1 Set(s) Central support poles, uPVC, 110mm,
in 3 sections with 2 connectors
7 1 Each Baseplate, 248mm Ø, with location lugs and
butyl rubber pad plate
8 1 Each Top of tube top hat section
9 12 Roll(s) Preformed mastic strip
10 1 Each DANGER DEEP WATER transfer sticker
11 21 Each Support bracket
12 240 Each Bolt, M8, GI
13 240 Each Nut, M8, GI
14 240 Each Washer, M8, GI
15 43 Each Nut, bolt, washer, M8, and
neoprene backed washer set
16 1 Each Nut, bolt, washer, M16, and
neoprene backed washer set
17 21 Each Roof retaining straps, large
18 1 Set(s) Washer, GI, 54mm OD x 18mm ID, (x3)
19 1 Set(s) Washer, rubber 54mm OD x 14mm ID, (x3)
20 1 Each Jubilee clip, 125mm

Packaging: Wooden Crate

4) WATER DISTRIBUTION/TAP STAND KIT, 6 taps - with details as per UNICEF Material Number S0005831 (See Catalogue: https://supply.unicef.org)

Water distribution kit comprising a tap stand with 6 taps, a kit to connect the tap stand to the water tank (below point 5), and an installation tools kit (below point 6).

The Water Distribution Kit (tap stand kit) for use with above water tank. The stand is made of hot dipped galvanized steel pipes or hot rolled galvanized steel sections. All pipes should be threaded as per ISO 7 (the thread cutting oil must be non-toxic type), and must be able to withstand rough handling during use.

Each water tank kit is supplied with not less than two (2) sets of distribution Tap Stand kits, and an appropriate connection hose kit with quick couplings for connecting to both the tap stand kits.

5/- Connection hose kit - included as per UNICEF material number S0005831 (See: https://supply.unicef.org):

Appropriate connection hose kit for functionally connecting the water tank with two tap stand kits, i.e. the following list is not exhaustive:

Item 1: 1 length of not less than 6 meter semi rigid hose, for the conveyance of water, plasticized PVC abrasion resistant hose, ozone and weather resistant, smooth bore, fitted with a shock resistant rigid PVC spiral, 50 mm diameter, each end fitted with 2 x 50 mm Guillemin couplings.
Collars
Item 2: 1 x Disposable spanner for tightening of collars.
Item 3: 2 x Spanners for Guillemin couplings.
Item 4: 2 x 50 mm hose clips.

6/- Tool kit = Installation tool kit - included as per UNICEF material number S0005831 (See: https://supply.unicef.org):

Item 1: 2 x Pick axes 7 lb. c/w hard wood shaft.
Item 2: 2 x Scoops (Irish shovel) with 54" straight wood handle.
Item 3: 2 x 18" Stillson pipe wrench.
Item 4: 1 x Barrier tape (500 m roll).
Item 5: 1 x Rope 6 mm, blue polypropylene x 50 m.
Item 6: 1 x Spirit level, 60 cm.
Item 7: 2 x Guillemin wrench 20-65 mm.
Item 8: 1 x Hank of hemp (200 g).
Item 9: 1 x Tube/can grease (400 g).

PACKAGING AND LABELING:
All the steel sheets for the tank must be packed in one substantial pallet with minimum clearance of 100 mm for forklift. The whole to be securely strapped together with steel bands and the ends protected with timber. The crate must be clearly marked with the name of the kit with the gross weight and dimensions clearly shown. Marks to be placed on the front and back of the case, as determined by the runners for forklift.
2. All the items for the tank liner and accessories must be packed in a sturdy timber crate with minimum 100 mm risers, for off-loading with jack poles. Items 7, 8, 9 and 10 must be pre-assembled. The crate must be marked with the name of the kit with the gross weight and dimensions clearly shown. Marks to be placed on the front and back of the case, as determined by the runners for the forklift.
3. All items for the roof cover must be packed in one sturdy timber crate with minimum 100 mm risers, for off-loading with jack poles. Crate must be clearly marked with the name of the kit with gross weight and dimensions clearly shown. Marks must be on the front and back of the case, as determined by the runners for the forklift.
4. Water Distribution kit (disassembled), the connection kit and installation tool kit must be packed in a sturdy wooden with parts well protected against damage during transportation on rough terrain.

PACKING LISTS
One packing list in a plastic bag to be securely fixed to the outside of the crate.
One packing list, including User's Notes to be enclosed in the crate in a grip-seal plastic bag.

ALTERNATIVE PRODUCTS:
S0009207 Water tank kit, Steel Frame, uPVC Roof, w.Liner,70m3
Related Products